|
Single Wall Flue |
|
SW430,
SW304 |
Single Wall flue systems manufactured in 430 BA and
304 BA. Suitable for use on gas & oil fired equipment. |
|
Vitrelux |
Vitrelux flue pipe manufactured from zero carbon
steel, coated both internally and externally with a high temperature
and acid resistant vitreous enamel coating. |
| SW Galv |
Single Wall ductwork manufactured in aluzinc coated
mild steel, suitable for ventilation & extraction. Can also be used
for flue dilution systems. |
|
CPS |
CPS Single Wall is produced from 316 stainless steel
0.5mm thick. It is a fully welded product suitable for use on a wide
range of heating process and ventilation applications including
condensing boilers. |
|
SW316 |
Single Wall 316 stainless steel ridged liner
available in 22g and 1mm. 22g available to Special Order Only. 1mm
conforms to BS6461, Part 2. |
|
Twin
Wall Flue |
|
Gas
Vent |
GV twin wall flue system manufactured from zalutite
outer casing and an aluminium inner with a 10mm air gap. Suitable
for both internal and external use on domestic gas fired appliances
which have a draught diverter. |
|
LTZ |
Twin wall 304 stainless steel inner, 10mm of
insulation and zalutite outer. Suitable for internal and external
use on gas fired, domestic and small commercial boilers with flue
gas temperatures up to 250°C continuous firing. |
| LT(LD/GV) |
Twin Wall flue system,
Aluminium inner liner, 25mm air gap and embossed aluminium (stucco)
outer liner. Suitable for use on gas & oil fired equipment with flue
gas temperatures not exceeding 260°C. |
|
PS |
Single & Twin Wall versions of this system have a
fully welded inner liner, capable of operating at pressures up to
1700mm wg. (A flanged product is available for higher pressures).
The system has been tested for four hours to the requirements of
BS476. |
|
LT (LT/SS),
MT,
HT,
HT
Plus |
Twin Wall Insulated flue systems for low, medium and
high temperature applications for gas & oil fired applications. LT
is suitable for gas temperatures up to 380°C, MT up to 540°C and HT
up to 740°C. Our HT system has a 2-hour fire rating for stability
and integrity, it is suitable for all fuels and is accredited with
the NF mark. Dimension sheet included.
|
|
Sundry Items |
|
Aquarius |
A Range of Silicone and EPDM Flexible Roof Flashings |
|
Lead Slates |
A Range of Flexible Lead Roof Flashings |
|
Rotorvent |
Aerodynamic Spinning Cowls |
|
Other Items |
|
|
Terminals |
|
Combivent |
Combivent Terminal is designed to allow the vertical
discharge of flue gases through a roof mounted unit, fitted with
louvers on all sides providing high and low level ventilation
requirements in accordance with BS6644. |
| Windvent |
The Midtherm Windvent is a natural ventilation
system operating on aerodynamic principles, allowing the provision
of an air supply, and a corresponding extraction rate, without the
need for any power source other than the control system. |
|
Natural Lighting |
|
DuctLight |
An efficient means of
illuminating any area by means of conducting natural daylight
through a Super reflective tube. |
|
Fan
Assisted |
|
Fluevent Fans |
A
range of inline Flue Boost Fans |
|
Fluevent Units and Fan
Dilution Systems |
The Fluevent Fan Dilution System is a low noise , low
cost, aesthetically pleasing alternative to conventional flue
dilution systems, which is easier to design and install than the
usual ductwork for flue dilution systems. |
|
Heating |
|
Radiant Heaters |
Gas
fired radiant tube heating, suitable for industrial & commercial
applications. Also provide spares and after sales service. |
|
|
